
Description
QSFP PSM IR4 are a high performance, low power consumption, long reach interconnect solution supporting 40G Ethernet, fiber channel and PCIe. It is compliant with the QSFP MSA and 40GbE PSM4. QSFP PSM IR4 is an assembly of 4 full-duplex lanes, where each lane is capable of transmitting data at rates up to 10Gb/s, providing an aggregated rate of 40Gb/s.
Features
● Full duplex 4 channel 1310nm parallel module
● Transmission data rate up to 11.3Gbit/s per channel
● SFF-8436 QSFP+ compliant
● Hot pluggable electrical interface
● Differential AC-coupled high speed data interface
● 4 channels 1310nm FP array
● 4 channels PIN photo detector array
● Maximum link length of 2km on G652 single mode fiber (SMF)
● Single male MPO(APC 8-degree) connector receptacle
● Maximum power consumption 3.5W
● Housing isolated from connector ground
● 3.3V power supply voltage
● RoHS 6 compliant
● Case operating temperature
     Commercial: 0 ~ +70℃
     Industrial: -40 ~ +85℃
Applications
● Infiniband Connectivity SDR/DDR/QDR
● 10/40 Gigabit Ethernet
● Data Centers and Storage Arrays
Absolute Maximum Ratings
| Parameter | Symbol | Min | Max | Unit | 
| Supply Voltage | Vcc | -0.3 | 3.6 | V | 
| Input Voltage | Vin | -0.3 | Vcc+0.3 | V | 
| Storage Temperature | Tst | -20 | 85 | ºC | 
| Case Operating Temperature | Top | 0 | 70 | ºC | 
| Humidity(non-condensing) | Rh | 5 | 95 | % | 
Recommended Operating Conditions
| Parameter | Symbol | Min | Typical | Max | Unit | 
| Supply Voltage | Vcc | 3.13 | 3.3 | 3.47 | V | 
| Operating Case temperature | Tca | 0 | 70 | ºC | |
| Data Rate Per Lane | fd | 10.3 | 11.3 | Gbps | |
| Humidity | Rh | 5 | 85 | % | |
| Power Dissipation | Pm | 3.5 | W | ||
| Link Distance with G652 | Rb | D | 2 | km | 
Specifications
| Parameter | Symbol | Min | Typical | Max | Unit | 
| Differential input impedance | Zin | 90 | 100 | 110 | ohm | 
| Differential Output impedance | Zout | 90 | 100 | 110 | ohm | 
| Differential input voltage amplitude | ΔVin | 300 | 1100 | mVp-p | |
| Differential output voltage amplitude | ΔVout | 500 | 800 | mVp-p | |
| Skew | Sw | 300 | ps | ||
| Bit Error Rate | BR | E-12 | |||
| Input Logic Level High | VIH | 2.0 | VCC | V | |
| Input Logic Level Low | VIL | 0 | 0.8 | V | |
| Output Logic Level High | VOH | VCC-0.5 | VCC | V | |
| Output Logic Level Low | VOL | 0 | 0.4 | V | 
 Note:
1.BER=10^-12; PRBS 2^31-1@10.3125Gbps.
2.   Differential input voltage amplitude is measured between TxNp and TxNn.
3.   Differential output voltage amplitude is measured between RxNp and RxNn.
Optical Characteristics
| Parameter | Symbol | Min | Typical | Max | Unit | Notes | |
| Transmitter | |||||||
| Centre Wavelengthc | λc | 1260 | 1310 | 1355 | nm | – | |
| RMS spectral width | ∆λ | – | – | 3.5 | nm | – | |
| Average launch power, each lane | Pout | -7.6 | – | 0.5 | dBm | – | |
| Difference in launch powerbetween any two lanes (OMA) | Ptx,diff | 6.5 | dB | – | |||
| Extinction Ratio | ER | 3.5 | – | – | dB | – | |
| Transmitter and dispersionpenalty (TDP), each lane | TDP | 2.6 | dB | – | |||
| Average launch power of OFFtransmitter, each lane | Poff | -30 | dBm | – | |||
| Transmitter Reflectance | RT | -12 | dB | ||||
| Eye Mask coordinates: X1, X2, X3, Y1, Y2, Y3 | SPECIFICATION VALUES0.25, 0.4, 0.45, 0.25, 0.28, 0.4 | Hit Ratio = 5×10-5 | |||||
| Receiver | |||||||
| Centre Wavelength | λc | 1260 | 1310 | 1355 | nm | – | |
| Stressed receiver sensitivity in OMA, each lane | SEN | -10.3 | dBm | 1 | |||
| Receiver sensitivity in OMA, each lane(10.3125Gb/s @ PRBS 2^31-1 and BER=10^-12) | -12.6 | dBm | |||||
| Maximum Average power at receiver input, each lane | 0.5 | dBm | – | ||||
| Difference in Receive Power between any Two Lanes(OMA) | Prx,diff | 7.5 | dB | ||||
| Receiver Reflectance | RR | -26 | dB | – | |||
| LOS Assert | LOSA | -30 | dBm | – | |||
| LOS De-Assert | LOSD | -14 | dBm | – | |||
| LOS Hysteresis | LOSH | 0.5 | dB | – | |||
Note:Measured with conformance test signal at TP3 for BER = 10e-12
Mechanical Dimensions

Ordering information
| Part Number | Product Description | 
| FTCQ-4X-PSMIR4 | 40Gb/s QSFP+ PSM IR4 up to 2km,0ºC ~ +70ºC | 
| FTCQ-4X-PSMIR4I | 40Gb/s QSFP+ PSM IR4 up to 2km,-40ºC ~ +85ºC | 
北亿纤通 | F-tone Networks
企业邮箱:sales@f-tone.com
企业手机:19081343401
企业电话:028-85255257
企业传真:028-85977702
注:本产品有全国产化型号可选
Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.
The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.ly freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.urther details are available from any F-tone Networks sales representative.e Networks sales representative.tive.s or others. Further details are available from any F-tone Networks sales representative.y F-tone Networks sales representative.

光学性能测试
测试光纤收发模块的眼图情况、接收灵敏度、消光比、波长、发光、光接收、电流和电压,以确保信号质量、传输的稳定性和可靠性。
Traffic Testing
测试误码率和丢包率,使其符合相应标准,确保收发器的性能。


光学性能测试
测试光纤收发模块的眼图情况、接收灵敏度、消光比、波长、发光、光接收、电流和电压,以确保信号质量、传输的稳定性和可靠性。
端面测试
检查光纤收发模块的端面并保持清洁,以实现更稳定的数据传输、更好的性能和耐用性。


兼容品牌:
华为 | 华三 | 中兴 | 锐捷 | Cisco | Juniper | Arista | Brocade |HPE ProCurve | HPE Aruba | HPE BladeSystem | HPE H3C | H3C | Dell | Extreme | HW | Generic | F-tone | Intel | Netgear | IBM | NVIDIA/Mellanox (Ethernet) | Ciena | Fortinet | Avago | Avaya | Alcatel-Lucent | D-Link | F5 | Ubiquiti | Mikrotik |Broadcom…..





