CFP Transceiver,100G,SR10

Description
The CFP optical transceiver module are a high performance, low power consumption, short reach(1m to 100m) interconnect solution supporting 100G Ethernet and Telecom. It is compliant with the CFP MSA and IEEE P802.3ba 100GBASE-SR10. F-tone Networks CFP SR10 modules offer 10 transmit and 10 receive asynchronous channels operating at up to 11.18Gbps per channel.
As shown in Figure 1, the transmitter side of the module consists of an array of VCSELs (Vertical Cavity Surface Emitting Lasers) and associated circuitry, which converts 10 parallel electrical data inputs to 10 parallel optical data output signals and also converts 10 parallel optical signals into 10 parallel electrical signals through an array of PIN photodiodes and associated circuitry.

Features
● Compliant to the CFPHardwareSpecification Version 1.4
● Compliant to the CFP MSA Management Interface SpecificationVersion 2.2
● Compliant to the IEEE 802.3ba(100GBASE-SR10)
● Transmission data rate up to 11.18 Gbit/s per channel
● Up to 300m on OM3 and 400m on OM4 MMF
● Power class 1 (<7W max)
● OTU4 compatible
● 10 channels 850nm VCSEL arraytransmitter
● 10 channels PIN photo detector arrayreceiver
● MDIO digital diagnosticinterface(Optional)and control capabilities.
● TX input and RX output CDR retiming
● Hot pluggable electrical interface
● Single 3V power supply
● RoHS 6 compliant(lead free)
● Utilizes a standard 24/20 lane optical fiber with MPO connector
● Case operating temperature
      Commercial: 0 ~ +70℃
      Industrial: -40 ~ +85℃

Applications
● 100GBE interconnects
● High-speed core router connections&Datacom/Telecom switch
● Data aggregation and backplane applications
● Proprietary protocol and density application

Absolute Maximum Ratings

Parameter	Symbol	Min	Max	Unit
Supply Voltage	Vcc	-0.5	3.6	V
Input Voltage	Vin	-0.3	Vcc+0.3	V
Storage Temperature	Tst	-40	85	ºC
Humidity(non-condensing)	Rh	5	85	%

*Exceeding any one of these values may destroy the device immediately

Recommended Operating Conditions

Parameter	Symbol	Min	Typical	Max	Unit
Supply Voltage	Vcc	3.13	3.3	3.47	V
Operating Case temperature	Tca	0		70	ºC
Data Rate Per Lane	fd	–	10.3125	11.18	Gbps
Power Dissipation	Pm			7	W
Low Power Mode Dissipation	Plow			2	W
Aggregate Bit Rate	BRaggr		103.125	111.8	Gbps

Electrical Characteristics

Parameter	Symbol	Min	Typical	Max	Unit	Notes
Differential input impedance	Zin	90	100	110	ohm
Differential Outputimpedance	Zout	90	100	110	ohm
Differential inputvoltage amplitude	ΔVin	120		820	mVp-p
Differential outputvoltage amplitude	ΔVout	300		820	mVp-p
Input Logic Level High	VIH	2.0		VCC+0.3	V	3.3V LVCOMS
		0.84		1.2	V	1.2V LVCOMS
Input Logic Level Low	VIL	-0.3		0.8	V	3.3V LVCOMS
		-0.3		0.36	V	1.2V LVCOMS
Output Logic Level High	VOH	VCC-0.2		VCC	V	3.3V LVCOMS
		1.0		1.5	V	1.2V LVCOMS
Output Logic Level Low	VOL	0		0.2	V	3.3V LVCOMS
		-0.3		0.2	V	1.2V LVCOMS

Note：
1.   Differential input voltage amplitude is measured between TxnP and TxnN.
2.   Differential output voltage amplitude is measured between RxnP and RxnN.

Optical Characteristics
Transmitter Optical Specifications (T = 25°C, VCC =3.3V +/- 5%)

Parameter	Symbol	Min	Typical	Max	Unit
Average Optical Power(per channel)	Pout	-7.6	-1	+2.4	dBm
Average Optical Power(per channel) – Disabled	Poff			-30	dBm
Optical Return Loss Tolerance				12	dB
Extinction Ratio	ER	3			dB
Center Wavelength	λc	840	850	860	nm
RMS Spectral Width	λ		0.5	0.65	nm
Transmit OMA,per Lane	TX_OMA/lane	-5.6		3	dBm
Difference in launch power between any two lanes(OMA)				4	dB
Transmitter and dispersion penalty,each lane	TDP/lane			3.5	dB
Transmitter eye mask	Compliant to IEEE802.3ba eye mask specification

Note：1.   Average optical power is measured at the output of the modules optical interface.

Receiver Optical Specifications (T = 25°C, VCC =3.3V +/- 5%)

Parameter	Symbol	Min	Typical	Max	Unit
Optical Power Sensitivity(per channel)	Pin min	–	-12	-9.9	dBm
Optical Power Saturation(per channel)	Pin max	+2.4dBm	–	–	dBm
Stressed Receiver Sensitivity	PS	–	–	-5.4	dBm
Center Wavelength	λc	840	850	860	nm
RMS Spectral Width	λ		0.5	0.65	nm
Optical Return Loss	Rl	12			dB
Damage Threshold		+3.4dBm			dBm
Optical modulation amplitude, each lane				3	dBm

Note：Optical power sensitivity is measured with BER@10^-12 at 10.3125Gbps per channel.

Mechanical Dimensions

Ordering information

Part Number	Product Description
FTC1-HG-SR10	CFP 100G SR10, 100m on OM3 MMF and 150m on OM4 MMF,0 ~ +70℃
FTC1-HG-SR10I	CFP 100G SR10, 100m on OM3 MMF and 150m on OM4 MMF,-40 ~ +85℃
FTC1-HG-CSR10	CFP 100G SR10, 300m on OM3 MMF and 400m on OM4 MMF,0 ~ +70℃
FTC1-HG-CSR10I	CFP 100G SR10, 300m on OM3 MMF and 400m on OM4 MMF,-40 ~ +85℃

北亿纤通 | F-tone Networks

企业邮箱： sales@f-tone.com
企业手机：19081343401
企业电话：028-85255257
企业传真：028-85977702

注：本产品有全国产化型号可选
本产品为CFP光模块，仅展示部分参数，如有需要，请联系我们。

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.

The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.