10G 1310nm 2km SFP+光模块

Features
● 10Gb/s serial optical interface compliant to 802.3ae
● Electrical interface compliant to SFF-8431specifications for enhanced 8.5 and 10 Gigabit small form factor pluggable module “SFP+”
● 1310nm FP transmitter, PIN photo-detector
● 2-wire interface for management specifications compliant with SFF 8472 digital diagnostic monitoring interface for optical transceivers
● Operating case temperature: 0 to 70 °C or-40 to 85 °C
● ll-metal housing for superior EMI performance
● Low power consumption
● Advanced firmware allow customer system encryption information to be stored in transceiver
● Cost effective SFP+ solution, enables higherport densities and greater bandwidth
● RoHS compliant

Applications
● High-speed storage area networks
● Computer cluster cross-connect
● Custom high-speed data pipes

ABSOLUTE MAXIMUM RATING

These values represent the damage threshold of the module. Stress in excess of any of the individual Absolute Maximum Ratings can cause immediate catastrophic damage to the module even if all other parameters are within Recommended Operating Conditions.

Parameters	Symbol	Min.	Max.	Unit
Power Supply Voltage	VCC	0	3.6	V
Storage Temperature	Tc	-40	85	。C
Operating Case Temperature	Tc	0	70	。C
	TI	-40	85
Relative Humidity	RH	5	95	%
RX Input Average Power	Pmax	–	0	dBm

RECOMMENDED OPERATING ENVIRONMENT
Recommended Operating Environment specifies parameters for which the electrical and optical characteristics hold unless otherwise noted.

Parameters	Symbol	Min.	Typical	Max	Unit
Power Supply Voltage	VCC	3.135	3.3	3.465	V
Power Supply Current	Icc			300	mA
Operating Case Temperature	TC	0	25	70	。C
	TI	-40	25	85

OPTICAL CHARACTERISTICS
The following optical characteristics are defined over the Recommended Operating Environment unless otherwise specified.

Parameters	Unit	Values
Operating Reach	m	0 – 2K
Transmitter
Center wavelength (range)	nm	1260 -1355
Launched power
– maximum (Average)	dBm	0.5
– minimum (Average)	dBm	-8.2
–  OMA(min)	dBm	-5.2
–  OMA-TDP (min)	dBm	-6.2
Average launch power of OFF transmitter (max)	dBm	-30
Extinction ratio (min)	dB	3.5
RIN12 OMA (max)	dB/Hz	-128
Optical Return Loss Tolerance (min)	dB	12
Receiver
Center wavelength (range)	nm	1260-1355
Receive overload (max) in average power(note 1)	dBm	0.5
Receive sensitivity (min) in average power(note 1)	dBm	-14.4
Receiver sensitivity (max) in OMA (note 2)	dBm	-12.6
Receiver Reflectance (max)	dB	-12
Stressed receiver sensitivity (max) in OMA(note 2)	dBm	-10.3
Vertical eye closure penalty (min)(note 3)	dB	2.2
Los Assert(min)	dBm	-30
Los Dessert(max)	dBm	-12
Los Hysteresis(min)	dB	0.5
Stressed eye jitter (min)(note 2)	UIp-p	0.3
Receive electrical 3dB upper cutoff frequency (max)	GHz	12.3
Receiver power (damage, Max)	dBm	1.5

Notes:
1.    Average optical power shall be measured using the methods specified in TIA/EIA-455-95.
2.    Receiver sensitivity is informative. Stressed receiver sensitivity shall be measured with conformance test signal for BER = 1x 10^-12.
3.    Vertical eye closure penalty and stressed eye jitter are the test conditions for measuring stressed receiver sensitivity. They are not the required characteristic of the receiver.
4.    Power budget is defined as the different between the Rx sensitivity and the Tx output power of the interface.
5.    Path penalty is intended as the power penalty of the interface between back-to-back and the maximum applied dispersion.

ELECTRICAL CHARACTERISTICS
The following electrical characteristics are defined over the  Recommended  Operating  Environment  unless otherwise specified.

Parameter	Symbol	Min.	Typical	Max	Unit	Notes
Data Rate		–	10.3125	–	Gbps
Power Consumption		–	800	1000	mW
Transmitter
Single Ended Output Voltage Tolerance		-0.3	–	4	V
Ccommon mode voltage tolerance		15	–	–	mV
Tx Input Diff Voltage	VI	180		800	mV
Tx Fault	VoL	-0.3		0.4	V	At 0.7mA
Data  Dependent  Input Jitter	DDJ			0.1	UI
Data Input Total Jitter	TJ			0.28	UI
Receiver
Single Ended Output Voltage Tolerance		-0.3	–	4	V
Rx Output Diff Voltage	Vo	300		850	mV
Rx Output Rise and Fall Time	Tr/Tf	30			ps	20% to 80%
Total Jitter	TJ			0.7	UI
Deterministic Jitter	DJ			0.42	UI

MECHANICAL
Comply to SFF-8432  rev. 5.0, the improved Pluggable form factor specification.

                                                     Key Mechanical Dimensions

订单信息

产品型号	封装	波长(-xx)	速率(xx)	传输距离 (-xx)	x	等级(x)
BYCS-131X-02Dxx	SFP+	13=1310nm  15=1550nm	1X=10.3GBP/s	02≤2km  10=10km  20=20km  40=40km	空 不带DDM  D 带 DDM	空 商业级  E 扩展级  I 工业级

北亿纤通 | F-tone Networks

企业邮箱： sales@f-tone.com
企业手机：19081343401
企业电话：028-85255257
企业传真：028-85977702

注：本产品有全国产化型号可选
本产品仅展示部分参数，如有需要，请您联系我们。

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.

The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.ts of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.